Moxa IOLOGIK W5340-T User Manual Page 93
- Page / 196
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ioLogik Cellular Micro RTU Controller Click&Go Logic
4-20
IF Conditions
IF conditions are events that trigger THEN/ELSE actions. Under the IF column, you can set up to 3
conditions that must be satisfied for the actions under the THEN/ELSE column to take place. As soon as the
IF conditions are satisfied, the specified THEN/ELSE action is performed. For example, an alarm can be
activated when a door is opened. Use the pull downs to specify the conditions and units of measurement (e.g.,
DI-0=OFF).
IF conditions can be specified as follows:
IF Conditions Operators Remark
DI ON, OFF, ON to OFF, OFF to ON, Change DI-x represents the channel number
Counter =, >, <, >=, <=, Change Counter-x represents the channel number.
Max Counter Value: 4,294,967,295
AI =, >, <, >=, <= AI-x represents the number of the channel.
Max Value: Depends on the analog modes
or the result of scaling. Internal
Register(Float) can be used as the
comparison or throughput setting
controlled by remote SCADA or a
Modbus/TCP program.
Relay =, >, <, >=, <= CurRelayCNT-x represents the current relay
counts for the channel.
Max Value: 4,294,967,295
Internal Register = Reg-x represents the number of the
internal
register.
x = 00 to 23 / Trigger Value: 0 to 255
Timer TIMEOUT Timer-x, x = 00 to 23
Max value: 4,294,967,295 seconds
Schedule Time, Range and Recurrence
Expansion Module
Connection Failure
0, 1
Virtual Channel =, >, <, >=, <= VC-x represents the channel number
System Start up N/A Activate when the system is starting up at
System Start
NOTE
The following IF Conditions are only supported
by ioLogik W5300 micro RTU controllers:
Expansion Module
Connection Failure
, Virtual Channel, and System Start-up.
- User’s Manual 1
- Table of Contents 3
- Introduction 6
- Quick Start Guide 7
- Architecture 7
- Product Features 10
- Appearance 10
- Package Checklist 11
- Product Selection Guide 12
- Product Specifications 12
- Getting Started 17
- Before Testing 18
- Laboratory Testing 19
- Configuring the DIO Channels 23
- Digital Output (Sink Type) 24
- Testing the I/O Device 25
- DIN Rail / Wall Mounting 26
- Network 28
- Detailed instructions: 29
- IP Address 30
- Export System Config 31
- Import System Config 31
- Utility: ioAdmin 32
- Features of ioAdmin 33
- Main Screen Overview 34
- Menu Bar 34
- Menu Bar: File 34
- Menu Bar: System 35
- Menu Bar: Sort 38
- Quick Links 38
- Menu Bar: Help 39
- Navigation Panel 40
- Main Window 41
- Server Info Panel 41
- Sync. rate status 42
- Status bar 42
- Server Settings Panel 43
- LAN Settings Panel 44
- I/O Configuration Panel 45
- Configuring Virtual Channels 47
- Configuring DIO Channels 49
- Counter Scaling 50
- Relay Count Monitoring 52
- Testing DI and DO Channels 53
- I/O Expansion Panel 54
- Active Tags Panel 57
- Active OPC: Redundancy Mode 58
- Heartbeat Interval 58
- Read/Write Privilege 59
- Active Tags 59
- Cellular Settings Panel 61
- Caller IDs 62
- Operation Mode Setting 62
- DDNS Settings 63
- Port Forwarding 64
- General Settings 65
- Manual Key/ESP 66
- ISAKMP/PSK 67
- Cellular Reconnection 68
- Meter/Sensor 70
- Network Statistics 71
- Watchdog Panel 72
- Click&Go Logic Panel 72
- Click&Go Logic 74
- Overview 76
- Click&Go Logic Basics 77
- Working with Rules 78
- I/O Configuration 79
- Analog Input Mode Selection 81
- Alias Name Configuration 81
- Testing the I/O Channels 82
- Defining Global Variables 83
- SNMP Trap Server 84
- E-Mail Server 84
- Active Message Server 86
- SMS Phone Book 86
- Working/Off Working Days 87
- FTP Settings 87
- Data Logging Profile List 88
- Working with Logic 91
- IF “A” THEN “B”, ELSE “C” 92
- IF Conditions 93
- Virtual Channel 95
- Relay (Counter) 95
- Schedule 97
- System Start-up 98
- THEN/ELSE Actions 100
- Counter 101
- Pulse Output 102
- Relay (Counts) 103
- Internal Register (Integer) 104
- SNMP Trap 105
- Active Message 105
- ATTENTION 105
- Short Message Service 107
- Data Log Start/Stop 108
- FTP Service 109
- Activating the Rule-set 110
- Import/Export Configuration 110
- Planning and Assistance 112
- Internet 120
- Statistics 122
- Log Profile Creation 124
- Log File upload with FTP 126
- Connecting to a SCADA System 130
- Setup Procedure 132
- Wake on Call 139
- Pin-outs and Cable Wiring 141
- Pinouts 142
- Cable Wiring 144
- Digital Output Sink Mode 145
- Relay Output 145
- Analog Input 145
- SMS Commands 146
- SMS Command Syntax: 147
- SMS Command Table 147
- Local I/O Commands: 148
- Expansion I/O Commands: 149
- Option Commands: 150
- Modbus/TCP Address Mappings 151
- Modbus Mapping 152
- Factory Default Settings 192
- Connection 194
- Cellular modem error codes: 195
- Service delay time 196
Related products and manuals for Cellular network devices Moxa IOLOGIK W5340-T
(105 pages)© 2020, manymanuals.com. All rights reserved. | 1.001 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals