Moxa IOLOGIK W5340-T User Manual Page 120
- Page / 196
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ioLogik Cellular Micro RTU Controller Planning and Assistance
5-9
NOTE
The following ioLogik E1200 models are supported for the I/O expansion: E1210 (16 DIs), E1211 (16 DOs),
E1212 (8 DIs and 8 DIOs), E1214 (6 DIs and 6 Relays), E1240 (8 DIs), E1241 (4AOs), E1242(4AI, 4DIs, and
4DIOs), E1260(6RTDs), and E1262(8TCs). ( Plus all Wide
-Temperature ioLogik 1200 models)
Using Modbus/TCP Protocol with Your Program
Scenario: Most customers would like to use their own HMI program to collect relevant information from
different remote sites. The most common way of doing this is to use Modbus/TCP. The following example
illustrates the procedure:
Environment:
1. Active OPC server: Public Static IP: 59.124.42.169
Internal Static IP: 192.168.19.19
2. Central site: Internal Static IP: 59.124.42.169
3. W5300 IP: 116.59.60.232 (a public IP is required)
Diagram:
We use ModScan32 to illustrate (ModScan32 is a product of WinTech, and can be downloaded from the WinTech
website).
Step 1: Install ModScan32 on your central host, with IP address 59.124.42.169.
Step 2: Set up your ioLogik W5300 Micro RTU Controller as follows:
• Connect DO-4 to DI-0 and DI-1
• Set DO-4 as 1Hz pulse output.
Step 3: Power on the W5300 and check the I/O status in ioAdmin. The status of DI-0 and DI-1 should have
changed to 1 Hz frequency.
Step 4: Configure the cellular settings on the Cellular Settings panel and the Active OPC Server’s IP Address on
the Active Tags panel, and then restart the ioLogik W5300. After restarting the system, the ioLogik W5300
should be assigned an IP address.
Step 5: If step 4 was completed successfully, remove the Ethernet console cable to force the W5300 get a
response from the cellular network.
Step 6: From your computer’s command line mode, ping IP address 116.59.60.232. If the ping is successful,
proceed to the next step.
NOTE
Some service provider
s (carriers) forbid and will filter this actiion.
Internet
CELLULAR
Network
Active OPC Server
IP: 59.124.42.169
Central Host
W5300
IP: 59.124.42.169
IP: 116.59.60.232
- User’s Manual 1
- Table of Contents 3
- Introduction 6
- Quick Start Guide 7
- Architecture 7
- Product Features 10
- Appearance 10
- Package Checklist 11
- Product Selection Guide 12
- Product Specifications 12
- Getting Started 17
- Before Testing 18
- Laboratory Testing 19
- Configuring the DIO Channels 23
- Digital Output (Sink Type) 24
- Testing the I/O Device 25
- DIN Rail / Wall Mounting 26
- Network 28
- Detailed instructions: 29
- IP Address 30
- Export System Config 31
- Import System Config 31
- Utility: ioAdmin 32
- Features of ioAdmin 33
- Main Screen Overview 34
- Menu Bar 34
- Menu Bar: File 34
- Menu Bar: System 35
- Menu Bar: Sort 38
- Quick Links 38
- Menu Bar: Help 39
- Navigation Panel 40
- Main Window 41
- Server Info Panel 41
- Sync. rate status 42
- Status bar 42
- Server Settings Panel 43
- LAN Settings Panel 44
- I/O Configuration Panel 45
- Configuring Virtual Channels 47
- Configuring DIO Channels 49
- Counter Scaling 50
- Relay Count Monitoring 52
- Testing DI and DO Channels 53
- I/O Expansion Panel 54
- Active Tags Panel 57
- Active OPC: Redundancy Mode 58
- Heartbeat Interval 58
- Read/Write Privilege 59
- Active Tags 59
- Cellular Settings Panel 61
- Caller IDs 62
- Operation Mode Setting 62
- DDNS Settings 63
- Port Forwarding 64
- General Settings 65
- Manual Key/ESP 66
- ISAKMP/PSK 67
- Cellular Reconnection 68
- Meter/Sensor 70
- Network Statistics 71
- Watchdog Panel 72
- Click&Go Logic Panel 72
- Click&Go Logic 74
- Overview 76
- Click&Go Logic Basics 77
- Working with Rules 78
- I/O Configuration 79
- Analog Input Mode Selection 81
- Alias Name Configuration 81
- Testing the I/O Channels 82
- Defining Global Variables 83
- SNMP Trap Server 84
- E-Mail Server 84
- Active Message Server 86
- SMS Phone Book 86
- Working/Off Working Days 87
- FTP Settings 87
- Data Logging Profile List 88
- Working with Logic 91
- IF “A” THEN “B”, ELSE “C” 92
- IF Conditions 93
- Virtual Channel 95
- Relay (Counter) 95
- Schedule 97
- System Start-up 98
- THEN/ELSE Actions 100
- Counter 101
- Pulse Output 102
- Relay (Counts) 103
- Internal Register (Integer) 104
- SNMP Trap 105
- Active Message 105
- ATTENTION 105
- Short Message Service 107
- Data Log Start/Stop 108
- FTP Service 109
- Activating the Rule-set 110
- Import/Export Configuration 110
- Planning and Assistance 112
- Internet 120
- Statistics 122
- Log Profile Creation 124
- Log File upload with FTP 126
- Connecting to a SCADA System 130
- Setup Procedure 132
- Wake on Call 139
- Pin-outs and Cable Wiring 141
- Pinouts 142
- Cable Wiring 144
- Digital Output Sink Mode 145
- Relay Output 145
- Analog Input 145
- SMS Commands 146
- SMS Command Syntax: 147
- SMS Command Table 147
- Local I/O Commands: 148
- Expansion I/O Commands: 149
- Option Commands: 150
- Modbus/TCP Address Mappings 151
- Modbus Mapping 152
- Factory Default Settings 192
- Connection 194
- Cellular modem error codes: 195
- Service delay time 196
Related products and manuals for Cellular network devices Moxa IOLOGIK W5340-T
(105 pages)© 2020, manymanuals.com. All rights reserved. | 2.529 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals