Moxa EDR-810 User Manual Page 102
- Page / 129
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Industrial Secure Router User's Manual Firewall
8-4
Destination IP
Setting Description Factory Default
All (IP Address)
This Firewall Policy will check all Destination IP addresses in the
packet
All
Single (IP Address) This Firewall Policy will check single Destination IP addresses in
the packet
Range (IP Address) This Firewall Policy will check multiple Destination IP addresses
in the packet
Destination Port
Setting Description Factory Default
All (Port number) This Firewall Policy will check all Destination port numbers in
the packet
All
Single (Port number) This Firewall Policy will check single Destination Port numbers
in the packet
Range (Port number) This Firewall Policy will check multiple Destination port
numbers in the packet
NOTE
The
Industrial Secure Router
’s firewall function will check if incoming or outgoing packets match the firewall
policy. It starts by checking the packet with the first policy (Index=1); if the packet matches this policy, it will
accept or
drop the packet immediately and then check the next packet. If the packet does not match this
policy it will check with the next policy.
NOTE
The maximum number of Firewall policies for the
Industrial Secure Router is 256.
Layer 2 Policy Setup (Only in Bridge Mode for
EDR-G902/G903)
When the Industrial Secure Router is in Bridge Mode (referring to section of Mode Configuration in Network
Settings), it provides an advanced Layer 2 firewall policy for secure traffic control, which depends on the
following parameters:
Interface From/To
Setting Description Factory Default
All (WAN1/WAN2/LAN) Select the From Interface and To interface None
WAN1
WAN2
LAN
Protocol
Setting Description Factory Default
Refer to table
“EtherType for Layer 2
Protocol” for a more
Select the Layer 2 Protocol in this Firewall Policy None
- Second Edition, August 2013 1
- Copyright Notice 2
- Trademarks 2
- Disclaimer 2
- Table of Contents 3
- Introduction 5
- Package Checklist 6
- Features 6
- Getting Started 7
- 1, VT100) 8
- Router’s Console 9
- Secure Router 10
- Quick Setting Profile 13
- Step 4: Enable services 15
- System Information 16
- User Account 17
- Create New Account 18
- Modify Existing Account 18
- Delete Existing Account 18
- Date and Time 19
- Warning Notification 20
- System Event Settings 21
- Port Event Settings 22
- Email Settings 22
- Syslog Server Settings 23
- Relay Warning Status 23
- SettingCheck 24
- Restart 27
- Reset to Factory Default 27
- Port Settings 27
- Link Aggregation 29
- The Port Trunking Concept 29
- Port Mirror 30
- Using Virtual LAN 31
- Configuring Virtual LAN 32
- 802.1Q VLAN Settings 33
- Quick Setting Panel 33
- Multicast 34
- Multicast Filtering 35
- IGMP Multicast Filtering 36
- Static Multicast MAC 36
- Enabling Multicast Filtering 36
- IGMP Snooping 37
- IGMP Snooping Settings 37
- IGMP Table 37
- Stream Table 38
- QoS and Rate Control 39
- CoS Mapping 40
- ToS/DSCP Mapping 41
- Rate Limiting 41
- MAC Address Table 42
- Interface 43
- Network Service 46
- DHCP Server 47
- Static DHCP 48
- IP-Port Binding 49
- SNMP Settings 50
- Dynamic DNS 52
- Security 53
- Authentication Certificate 54
- Trusted Access 54
- Monitor 55
- Port Statistics 56
- Event Log 57
- Functions 59
- Configuring Basic Settings 61
- Accessible IP 62
- Password 63
- Configuration File 68
- Network Settings 70
- WAN1 Configuration 71
- Using DMZ Mode 77
- LAN Interface 77
- Communication Redundancy 78
- WAN Backup Configuration 79
- System Log 81
- Routing 83
- Unicast Routing 84
- Routing Table 86
- Network Redundancy 87
- Configuring STP/RSTP 88
- Configuring Turbo Ring V2 90
- Layer 3 Redundant Protocols 92
- Network Address Translation 93
- NAT Concept 94
- 1-to-1 NAT 94
- N-to-1 NAT 96
- Port Forward 97
- Firewall 99
- Policy Concept 100
- Policy Overview 100
- Policy Configuration 100
- EDR-G902/G903) 102
- Quick Automation Profile 104
- Policy Check 106
- Modbus TCP Policy 108
- Overview 114
- IPSec Configuration 114
- IPSec Settings 115
- Key Exchange (IPSec phase I) 117
- IPSec Status 119
- X.509 Certificate 119
- Certificate Generation 120
- Certificate Setting 121
- Local Certificate Upload 121
- L2TP Configuration 122
- VPN Plan 123
- Diagnosis 125
- LLDP Function Overview 126
- LLDP Setting 126
- LLDT Table 127
- MIB Groups 128
© 2020, manymanuals.com. All rights reserved. | 3.687 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals